Right here down the page you will find a good deal of very good facts pertaining to Tools You Need to Install a New Bathtub .
Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate rapidly; if you need to open a wall to remove the old tub and place the new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the task and fit trying it. Rather than working with a service provider to take control of a halfway-completed task, it is much better to take into consideration utilizing one before you start. Chances are you may need a specialist plumber to make tube links.
This post will certainly assist you set up a brand-new bathtub in your shower room if you have actually already bought a brand-new tub as well as do not need to transform the arrangement of your previous supply of water pipelines.
Your tools and also material checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome due to the limited access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin making sure that the washing machines remain in place in between the faucet as well as the sink. Protect the tap in place with the maker supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of the two wood boards under its feet, place the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub until the spirit level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bath tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bath tub has been made use of at least when as this will certainly resolve it right into its last setting.
Planning for the Installment
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last placement.
Tiling Around the Tub
In the location where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and the tiling, leading to difficulties with dampness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can fracture rather very early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently offered on the marketplace. It is suggested to fit the tiles using waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on Tools You Need to Install a New Bathtub , I figured sharing that piece of content was worth the trouble. Sharing is caring. Helping others is fun. I take joy in reading our article about How to Install a Bathtub Yourself.
Protect your home, dial!